+- The Screwed Gamers Community Forums (http://screwedgamers.com/forum)
+-- Forum: Home (http://screwedgamers.com/forum/forumdisplay.php?fid=1)
+--- Forum: Welcomes and Introductions (http://screwedgamers.com/forum/forumdisplay.php?fid=3)
+--- Thread: How to Build a Boat Bench Seat? (/showthread.php?tid=1235)
How to Build a Boat Bench Seat? - mmws256w - 09-22-2021
DIY projects allow you to achieve the result that you desire. Utilizing your skills and artistic talents is related to this matter, and it’s also a way to save some bucks. With regards to this, many boaters can manage how to build a boat bench seat by themselves.
You may have wood for building boat seats. Some upgrades can be done by adding cushion and vinyl. Once you choose a design, you can start collecting materials.
If you’re groping for design ideas, this article will show you DIY boat bench seats that will surely please you. You can follow them to refurbish or renovate a boat.
Various boat styles showcase different angles and lines. Wide and deep hulls are the main characteristics of workboats, while sailboats are thin and long. Nonetheless, a wooden banquette would be fantastic on both of these vessels. Here are the steps:
Step 1. Take off Metal and Trim
A banquette is a bench along the wall. Therefore, you have to consider the needed space and shape for it. The center section of the boat is where you need to lay down this project.
To get started, you have to remove metal or trim but you must keep the pieces for reconnection later on. You may also need to take off logos and insignias that are still useful.
Step 2. Cutting the Chosen Area
Use chalk to draw a line on your chosen area then you can run the chainsaw over it. Cutting the area should be even and consistent. You may need to tidy up the cutting with a circular saw.
You have to be attentive while doing it as there may be some screws. These tiny pieces of hardware may be hiding underwood plugs.
Step 3. Cleaning
Get rid of the debris created by cutting since it can block from cutting the bottom part.
Step 4. The Bench Base
Use two pieces of 2×4 wood and place them 16 inches above the pontoon boat furniture with the support from screws for wood. This step is not only for building the base but hull reinforcement as well.
Get ¾-inch plywood to be added over the 2×4 woods with screws. This will strengthen the structural integrity that may have temporarily gone due to the cuttings that were made.
Step 5. Seat Back
You may recycle some wood that just lay around or V-groove soffit panels. Get measurement from the seat to the boat anchor for the preparation of the seatback.
To ensure that you’re going to create comfortable seats, add horizontal wood blocks that tilt at a slight angle. Install the seatback with 15-gauge finish nails.
Step 6. Seat Attachment
You may choose any suitable wood for the seat. Mahogany and tropical hardwoods like ipe are the best examples. Pre-drilled screw holes should be done before assembling the parts. Make planks for the bench size that you like and fasten them with stainless wood screws.
Step 7. Painting the Banquette
If you use recycled wood with some paint on it, you need to sand it before applying a new coat.
Step 8. The Last Touch for Refinement
You have to add a routed edge over the wooden seat. Then, you can put back the metal and insignia that you removed when starting this project.
The finishing touches will be covering the back panels with new paint, applying oil on the wood to have an attractive sheen, and sealing the original parts with polyurethane.
When thinking of comfortable bench seats for boats, cushions and vinyl may be the first things that come into your mind. You can skip buying ones for your aluminum boat and instead, make them yourself for customization.
So, here’s a guide on how to make a boat rear bench seat if you don’t mind sewing some seat cover.
Making a rectangular box frame is the very first step. Make three sides for the lower portion, and they will touch the transom and the floor. Its top will be able to flip and access the engine.
Make some plywood strips based on the measurement of the bench seat. You may have a shop cut it for you. Some 1”x1.5” pressure treated lumber, waterproof wood glue, and 1” staples are the things that you need to put the pieces together.
After forming the box out of the plywood strips, get rid of splinters by sanding. This process can also break the edges to prevent damaging the vinyl. After sanding, you can apply two coatings of paint.
Once the glue has dried, place it on the designated area in your boat. It’s sturdy and it won’t give you problems.
Step 2. Setting the Vinyl Down
You don’t have to put vinyl at the bottom of the box. An extra piece is needed to be wrapped under the seat. Just apply more effort in working for a nice appearance and allow a vinyl skirt to hang.
Make sure to leave a margin of about half an inch for sewing the edges. This is enough to match the cording’s size. Use the double-sided tape to hold the cording and make it curved without twisting or binding.
If you know how to use the sewing machine, you’ll be fine. But if not, you can ask someone to do it for you. When vinyl is sewn properly, you can install the bench.
Step 3. Cutting the Foam
Measure the amount of foam that you need, then mark it. Cutting can be done with an electric knife. Give ½” extra to ensure that the vinyl cushion is stuffed nicely. When you have the right piece of foam, glue it on the top of the box.
Batting should be added on the sides for some cushioning with the roughly estimated size. It gives the seat a fuller look. Use a Loctite adhesive to glue it and trimming is needed once it sits in the right place.
Step 4. Adding the Vinyl by Stapling
Stapling creates a serious grip and adequate strength to hold the vinyl in place. It’s best to use stainless staples. You can begin on the opposing side and work your way to finish tucking the whole piece of vinyl.
Just keep pulling, stapling, and tucking to obtain a neat result. At this point, you have finished a bench seat or a motor box for your aluminum boat.
As long as you have time, resources, and willingness to work, there’s no reason that you won’t try following the steps on how to build a boat bench seat. You can choose the color, design, size, and materials that you like from these two guides.
Some boaters want to customize the looks of their boats to represent their personalities. No one is stopping you from doing so! It can be a technique to give life to an old boat. Also, you can always make a bench seat in a set-up that brings comfort.
Did you find this article helpful? If yes, share with anyone who would need this.
It’s the time of the year again when being out on the water is the best place to be. In the heat of the summer sun, there’s really nothing like sitting on a pontoon boat to just drift on a calm lake or spend an entire afternoon fishing. Pontoon boats get a lot of attention during the summer months, and it’s only right to take preventative measures in order to keep the health of your boat in check. One of the easiest ways you can do this is by protecting the pontoon’s seats using seat covers. If you’re thinking about buying pontoon folding boat seat covers, here is a quick guide on what you should look for.
Material
Pontoon seat covers are made out of many different kinds of materials. The lowest end in the spectrum would be a simple plastic tarp. Although plastic tarps will do the job of covering your seats, they aren’t particularly durable. Plastic tarps are great alternative for quick-fix solutions, but they are not permanent options.
The next step up to plastic would be canvas tarps. Canvas tarps have long been used as a general cover-up material in boating. They are more durable than plastic in many ways. However, they are also more susceptible to mildew and mold. Canvas tarps today are most often referred to as marine vinyl. It’s still a good alternative if you prefer to use it, but canvas is also easy to stain. Either way, your canvas will definitely protect your pontoon boat seats, but they won’t last as long untreated. If you want your marine vinyl to last longer and protect your flip up boat seat better, you can treat them a waterproof and/or UV spray. The best materials for pontoon seat covers are vinyl blends or polyester. These materials are highly durable and easy to take care of. They are also more resistant to the elements; therefore, they can protect your seats better. Most vinyl blends also offer some breathability factors, so mold and mildew won’t have much room to grow in—even in the most humid conditions.
Size
You might automatically think that larger is better when it comes to pontoon boat covers, but that’s not necessarily true. Although a larger size will allow you to cover more area, it’s important to measure fit more than anything. Since pontoon boats are exposed to the elements continually, a fitted seat cover will do a better job in protection. Any excess room caused by an unfitted cover will just be excess room for more water or air to enter and damage your pontoon seats.
This is why it’s important to measure your pontoon seats before you go out looking for seat covers. This article discusses how you can measure your seat covers properly. Once you have the dimensions written down, you can then continue shopping for pontoon seat covers. Make sure you check your dimensions against the size of the covers before you purchase. It also helps to read reviews regarding the size of the cover from those that have purchased the same product before. You can also get information from the manufacturer of both the seat cover and your low back folding boat seat.
Other things to look for
Apart from material and size to consider, you might want to also think about a few other things before you buy a pontoon seat cover. First, you might want to think about ease of use and storage. When you’re not using your pontoon seat covers, where are they going to go? Can they easily be folded up and stowed away someplace on your pontoon boat?
There are also seat covers that might utilize the use of zippers or elastic. Some people prefer seat covers that will just slip over your pontoon seats. But there are others that are so fitted; you’d have to zip them up in place. There are seat covers that come with enclosures and others that don’t. It might not matter to some people, but style and color matter to others. You might find that a lot of pontoon seat covers come in a white color, neutral, or blue color. Whites and neutral colors reflect the sunlight better than darker colors.